Milnor Emerald EX-15 Скачать руководство пользователя страница 18

Страница: 18 / 87

Washing

•

Press the button for the desired program.

•

Now the LEDs alongside the program symbols
will show what the selected program consists of.

•

Press the button(s) for any options required.

•

This option button gives a longer extraction time
on "Hot", "Warm", "Cold", "Delicate" and "Perm
Press" programs.

•

This option button gives "Gentle action" in all
programs except "Delicate" which has gentle
action as standard.

NOTE!

Gentle actions consists of 6 seconds pause,
as opposed to 18 seconds rotation and 6
seconds pause for Normal action.

•

Add the correct amount of detergent and fabric
softener.

•

Press the START button.

3426

2288

2289

2290

3427

3435

Fig.

Operating Instructions

Fig.

Perm Press

Quick-Wash

START

Hot

Warm

Cold

Delicat

Heavy Soil

Heavy Soil Prewash

Prewash

Wash

Rinses

Final Extract

Extra Extract

Doorlock delay

Door unlocked

Add bleach if desired

Rinse 1

Rinse 2

Rinse 3

Softener

START

Fig.

Содержание Emerald EX-15
























































































Результаты поиска

Содержание Emerald EX-15

Отзывы:

Milnor Emerald EX-15, Руководство по эксплуатации и техническому обслуживанию, Страница: 18 / 87

Результаты поиска

Содержание Emerald EX-15

Отзывы: