Milnor Emerald EX-15 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 87

Milnor Emerald EX-15 Скачать руководство пользователя страница 68

64

Trouble shooting

Error codes which may arise on the control panel display

Error code/symptoms

Fault-finding

Cause/Action

Turn the machine’s wall switch off and on again.
Start a program.

Error code returns

No error code

Remove PCB connector X74 on program control
unit PCB. Turn the machine’s wall switch off and
on again. Start a program. Check whether the
error displayed is 04E or 05E.

04E

05E

Put back X74. Disconnect the link between
wiring and sensor by the temperature sensor.
Turn the machine’s wall switch off and on again.
Start a program. Check whether the error
displayed is 04E or 05E.

05E

04E

05E

Temperature sensing
indicates temperature above
98

°

C (short-circuit).

2316

X74

2

1

3399

Temperature
sensor

Transient fault.

Fault in temperature sensing
device on program control
unit PCB. Replace PCB.

Temperature sensor faulty.
Replace sensor.

Fault in wiring to temperature
sensor. Check wiring and
replace if necessary.

Rough values on the temp.
sensor

T (

°

C)

R (ohm)

19

6100

20

5850

21

5600

22

5350

23

5100

«
...
66
67
68
69
70
...
»

Содержание Emerald EX-15
























































































Отзывы:

Нет отзывов