MicroNet SP5563A Скачать руководство пользователя страница 52

Страница: 52 / 132

Assign a camera function: Preset, Sequence, Autopan or Cruise, and

specify a Preset Point / Sequence Line / Autopan Path / Cruise Line for

the camera to perform at an alarm occurrence.

NOTE:

Please refer to the sections through

Preset Programming

Sequence Line Programming

for details of

Preset Point /

Cruise Line / Autopan Path / Sequence Line setups.

If the selected function is <Preset>, it is required to enter its dwell time (1

sec. to 256 sec.) in the corresponding field as shown below. When the

alarm is triggered, the camera will go to the selected Preset Point and

stay there for a user-defined period of time. As for other function modes,

the camera will keep executing the specified function; to stop the

performance, simply change the camera’s status.

NOTE:

The dwell time is only adjustable when <Preset> is

selected. When the dwell time is up, the camera will go back to its

trigger position and recheck the alarm pin status.

Send HTTP notification

Check this item, select the destination HTTP address, and specify the

parameters for event notifications by <Alarm> triggered. When an alarm

is triggered, the notification can be sent to the specified HTTP server.

For instance, if the custom parameter is set as “

action=1&group=2

”, and

the HTTP server name is “

http://192.168.0.1/admin.php

”, the notification

will be sent to HTTP server as “

http://192.168.0.1/admin.php?

action=1&group=2

” when alarm is triggered.

Record Video Clip

Check this item and select a video recording storage type, <SD Card> or

<NAS> (Network-Attached Storage). The alarm-triggered recording will
be saved into the microSD card or the NAS.

Pre-trigger buffer recording function allows users to check what

happened to cause the trigger. The pre-trigger buffer time range is from 1

sec. to 3 sec. Select <Upload for

sec> to set the recording duration

after alarm is triggered. The setting range is from 1 sec. to 99999 sec.

Select <Upload during the trigger active> to record the triggered video

until the trigger is off.

Содержание SP5563A





































































































































Результаты поиска

Содержание SP5563A

Отзывы:

Похожие инструкции для SP5563A

Бренды по названию

Популярные бренды

MicroNet SP5563A, Руководство пользователя

Результаты поиска

Содержание SP5563A

Отзывы:

Похожие инструкции для SP5563A

Бренды по названию

Популярные бренды