MicroNet SP5563A, Руководство пользователя

Страница: 10 / 132

10
3. Installation
Please read the instructions provided in this chapter thoroughly before
installing the Box IP Camera.
3.1 Power and Ethernet Cable Connection
Power Connection
Make sure the camera’s power cable is correctly and firmly connected; refer
to the pin definition table in section
2.2 Camera’s Connectors . If using Power
over Ethernet (PoE), make sure Power Sourcing Equipment (PSE) is in use
in the network.
Ethernet Cable Connection
Use of Category 5 Ethernet cable is recommended for network connection;
to have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the IP
Camera, and the other end of the cable to the network switch or PC.
NOTE: In some cases, you may need use an Ethernet crossover
cable when connecting the IP Camera directly to the PC.
Check the status of the link indicator and activity indicator LEDs; if the LEDs
are unlit, please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
3.2 Lens Mounting
If use C-Mount lens, after removing the camera’s plastic cover, users need
to mount the C/CS mount adapter to the camera. Then attach the lens onto
the C/CS mount adapter, as the illustrations shown below.
C/CS Mount Adapter Completion
3.3 Alarm Application
The camera equips one alarm input and one relay output for alarm
application. Refer to alarm pin definition below to connect alarm devices to
the IP Camera if needed.
10
3. Installation
Please read the instructions provided in this chapter thoroughly before
installing the Box IP Camera.
3.1 Power and Ethernet Cable Connection
Power Connection
Make sure the camera’s power cable is correctly and firmly connected; refer
to the pin definition table in section
2.2 Camera’s Connectors . If using Power
over Ethernet (PoE), make sure Power Sourcing Equipment (PSE) is in use
in the network.
Ethernet Cable Connection
Use of Category 5 Ethernet cable is recommended for network connection;
to have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the IP
Camera, and the other end of the cable to the network switch or PC.
NOTE: In some cases, you may need use an Ethernet crossover
cable when connecting the IP Camera directly to the PC.
Check the status of the link indicator and activity indicator LEDs; if the LEDs
are unlit, please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
3.2 Lens Mounting
If use C-Mount lens, after removing the camera’s plastic cover, users need
to mount the C/CS mount adapter to the camera. Then attach the lens onto
the C/CS mount adapter, as the illustrations shown below.
C/CS Mount Adapter Completion
3.3 Alarm Application
The camera equips one alarm input and one relay output for alarm
application. Refer to alarm pin definition below to connect alarm devices to
the IP Camera if needed.
10
3. Installation
Please read the instructions provided in this chapter thoroughly before
installing the Box IP Camera.
3.1 Power and Ethernet Cable Connection
Power Connection
Make sure the camera’s power cable is correctly and firmly connected; refer
to the pin definition table in section
2.2 Camera’s Connectors . If using Power
over Ethernet (PoE), make sure Power Sourcing Equipment (PSE) is in use
in the network.
Ethernet Cable Connection
Use of Category 5 Ethernet cable is recommended for network connection;
to have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the IP
Camera, and the other end of the cable to the network switch or PC.
NOTE: In some cases, you may need use an Ethernet crossover
cable when connecting the IP Camera directly to the PC.
Check the status of the link indicator and activity indicator LEDs; if the LEDs
are unlit, please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
3.2 Lens Mounting
If use C-Mount lens, after removing the camera’s plastic cover, users need
to mount the C/CS mount adapter to the camera. Then attach the lens onto
the C/CS mount adapter, as the illustrations shown below.
C/CS Mount Adapter Completion
3.3 Alarm Application
The camera equips one alarm input and one relay output for alarm
application. Refer to alarm pin definition below to connect alarm devices to
the IP Camera if needed.