Michell Instruments XZR-400-BM Скачать руководство пользователя

Страница: 41 / 102

XZR400 Series User’s Manual

Michell Instruments

INSTALLATION

2.13 Gas

Connection

To ensure that the sample gas is properly

conditioned a sampling system might be

required.

Contact Michell Instruments if you wish to order

a suitable sampling system.

Sample gas connections are made via the gas input and gas output ports located on

the back panel (XZR400A1), bottom panel (XZR400A2), side panel (XZR400A3) or front

panel (XZR400A4) of the analyzer.

Both the input and output gas connections are 1/8” stainless steel Swagelok

couplings.

NOTE: To facilitate ease of connection to the port, at least 75mm (3") of the

tubing coming out of the gas inlet port must be straight.

The method of connecting to the gas inlet and gas outlet ports is as follows:

Connect the gas source from the sample system to the Swagelok

tting

at the inlet port on the instrument using 1/8” stainless steel tubing.

Tighten the

tting as much as possible by hand and tighten again with a

7/16”

at wrench (approximately 1¼ turns).

Connect the gas outlet port in a similar manner to that described in

Step 1 using 1/8” stainless steel tubing.

If you undo the fi tting again and reconnect it, fi rst tighten up by

hand and then tighten using a 7/16” fl at wrench with no more

than a 1/8 turn.

DO NOT OVER-TIGHTEN.

NOTE: Maximum sample pressure is 2 barg (29 psig).

NOTE: Sample is vented to atmosphere. Depending on the location of the

analyzer it may require a vent line to a safe location that is freely ventilated.

Содержание XZR-400-BM







































































































Результаты поиска

Содержание XZR-400-BM

Отзывы:

Похожие инструкции для XZR-400-BM

Бренды по названию

Популярные бренды

Michell Instruments XZR-400-BM, Руководство пользователя

Результаты поиска

Содержание XZR-400-BM

Отзывы:

Похожие инструкции для XZR-400-BM

Бренды по названию

Популярные бренды