Michell Instruments XZR-400-BM Скачать руководство пользователя

Страница: 42 / 102

XZR400 Series User’s Manual

97472 Issue 3, August 2018

OPERATION

3 OPERATION

It is recommended that the user becomes familiar with Section 2 of this manual in which

all the equipment controls, indicators, the elements of the display and the overall menu

structure are described.

Prior to operation, the analyzer must have been connected to the correct electrical

power supply and the relevant analog and alarm outputs connected to external systems

as described in Section 2.

On delivery, the instrument will have been set-up with a standard set of default

parameters de

ning the operation of the analyzer. These parameters can be changed

as required by means of the

Main Menu

3.1

General Operational Information

The input gas must be at a pressure of less than 2 barg (29 psig). A pressure regulator

is recommended when above 2 barg (29 psig) for better

ow control. The outlet of the

system must be at atmospheric pressure.

NOTE: If the outlet is at higher pressure than atmospheric an optional process

pressure correction is necessary. Please consult Michell Instruments in this

case.

The instrument is designed to operate with a gas

ow of 2 l/h ±1 l/h.

NOTE: For best results ensure that the sampling system is as close as possible

to the XZR400 Series Analyzer.

For all applications the sample gas is taken into the instrument via the gas inlet port

located on the bottom panel of the analyzer, from where it passes into an oven chamber.

The gas

ow rate is then measured on the outlet side of the sample chamber, prior to

being exhausted from the instrument via the gas outlet port.

The

ow, necessary for the sample gas circulation, is generated by the sensor oven

which utilizes the heat convection principle. The hot sample gas from the sensor oven is

pushed by the hot oven gases, which are still in the oven. On the way out of the oven

the sample gas cools, passing through the gas outlet port, and is carried away by the

main gas

ow.

The XZR400 Series Analyzers are suitable for the measurement of oxygen in a wide

variety of clean and dry gases. It will not contaminate high purity gases and is safe for

use in critical semiconductor and

bre optic manufacturing applications.

It is possible to continuously visualize the oxygen concentration in the range between

0.01 ppm and 25% oxygen. If required, the analyzer can display the MSRS voltage, the

oven temperature and the temperature of the cold junction in the thermocouple.

Содержание XZR-400-BM







































































































Результаты поиска

Содержание XZR-400-BM

Отзывы:

Похожие инструкции для XZR-400-BM

Бренды по названию

Популярные бренды

Michell Instruments XZR-400-BM, Руководство пользователя

Результаты поиска

Содержание XZR-400-BM

Отзывы:

Похожие инструкции для XZR-400-BM

Бренды по названию

Популярные бренды