Michell Instruments XZR-400-BM Скачать руководство пользователя

Страница: 40 / 102

XZR400 Series User’s Manual

97472 Issue 3, August 2018

INSTALLATION

2.12.2 Alarm Output Connections

Two alarm relays are provided and are connected to the instrument via the terminal

block on the back panel of the analyzer.

The signal outputs will be connected to external systems that can

potentially infl uence the operation of the process.

The alarm level signals could also be at mains potential so it is

essential that, before connecting these signal lines, checks are

made to ensure that these inputs are not live and that it is safe to

handle them.

Alarms 1 and 2 are concentration alarms. The direction of the activation N/O or N/C, as

well as the hysteresis, can be con

gured.

The output contacts are normally open and potential free. The relay switching capability

is 10 W max (up to 100 V or up to 0.5 A).

The method of connection is as follows:

Always use screened cable to connect the output to the external

device.

Alarm 1

1. Strip back the two wires for the alarm 1 output leads, exposing

approximately 6mm (0.25") wire and clamp them into the two screw ports
labelled as

Alarm 1

Do not overtighten the screw.

Connect the screen to the ground port.

Alarm 2

1. Strip back the two wires for the alarm 2 output leads, exposing

approximately 6mm (0.25") wire and clamp them into the two screw ports
labelled as

Alarm 2

Do not overtighten the screw.

Connect the screen to the ground port.

Содержание XZR-400-BM







































































































Результаты поиска

Содержание XZR-400-BM

Отзывы:

Похожие инструкции для XZR-400-BM

Бренды по названию

Популярные бренды

Michell Instruments XZR-400-BM, Руководство пользователя

Результаты поиска

Содержание XZR-400-BM

Отзывы:

Похожие инструкции для XZR-400-BM

Бренды по названию

Популярные бренды