Meler STARBI Скачать руководство пользователя страница 54

Страница: 54 / 73

FOCKE MELER GLUING SOLUTIONS

4-26

USE

39.

RESTORE DEFAULT VALUES

screen.

Allows you to delete all the changes made to the system and leave the

unit with the factory-set default parameters. After pressing, the following

confirmation message will appear:

STARBI.

Are you sure

you want to restore

the factory settings?

Yes

STARBI.

Configuration

Extra settings

Password

Restore default

• Continue after the Reset:

This activated option disables the STOPPED

mode so that is not necessary to press the STOP key to switch to

RUNNING mode. This option is used when the unit is in an inaccessible

area to the operator.

Attention:

If this option is used, the user is recommended to avoid an untimely

start-up of the unit by connecting the external inhibit signal and activating the

‘Enable inhibit signal’ option.

• Enable inhibit signal:

Enables or disables the external inhibit signal

from a main machine or a PLC, so that it is possible to pass with this

signal from STOPPED mode (0 V) to RUNNING mode (24 V) and vice

versa.

• Sound with alarm:

Activates or deactivates the sound when an alarm is

produced.

• Screensaver time:

Programs the time when the screensaver on the

display is activated.

• Activate or deactivate Modbus communication (only for equipment

with Modbus - optional).

Once activated, the desired values of “Node”

and “Baudrate” can be set up.

Содержание STARBI










































































Результаты поиска

Содержание STARBI

Отзывы:

Meler STARBI, Инструкция по эксплуатации, Страница: 54 / 73

Результаты поиска

Содержание STARBI

Отзывы: