Meler STARBI Скачать руководство пользователя страница 19

Страница: 19 / 73

INSTALLATION

3-1

MA-5151-ENG

PATTERN CONTROLLER STARBI

3. INSTALLATION

Warning:

The pattern controllers are installed in equipment provided with

current technologies and with certain foreseeable risks. Therefore, only

qualified personnel with sufficient training and experience should be allowed

to use, install or repair these devices.

Introduction

The pattern controllers are supplied with the complete 5 metre power cable

(except the pattern controller with 2 outputs) and the manual on a USB device.

The rest of the accessories will be requested apart.

Installation requirements

- Have the corresponding adhesive installation, with its applicators

prepared with the connection for the controller

- Ensure that the space set aside for this device enables the location,

connection and use of the entire system.

- Check that the electrical supply meets the requirements of the device

to be used.

Electrical consumption

Before connecting the pattern controller:

- Take into account the total consumption of the installation and provide

a current supply for the power rating indicated.

- Make sure that the voltage to which the device is to be connected is the

same as that indicated on the nameplate of the unit.

- Connect and check that the installation has a good ground connection.

Warning:

Risk of electrocution. Even when the unit is turned off, tension

remains in the input terminals, which could be dangerous for internal

manipulation of the unit.

- Install a circuit breaker to protect against short-circuits and a residual

current device as personal protection against earth leakages.

- The power associated with these protections is indicated on the

nameplate of the controller.

Содержание STARBI










































































Результаты поиска

Содержание STARBI

Отзывы:

Meler STARBI, Инструкция по эксплуатации, Страница: 19 / 73

Результаты поиска

Содержание STARBI

Отзывы: