Meler STARBI Скачать руководство пользователя страница 49

Страница: 49 / 73

MA-5151-ENG

PATTERN CONTROLLER STARBI

USE

4-21

30.

ADVANCED OPTIONS

screen.

These parameters are configured in the same way as the products by times

but with values in millimetres (mm). The analogue outputs are configured in

ramp mode to have a variable output depending on the speed.

31.

MANUAL MODE

selection screen.

It is selected from the MENU screen.

STARBI.

Product

Manual mode

Statistics

Installation

Settings

Alarms

STARBI.

120 s

Manual mode

Dot bead

Analog output 1

124.7 mm.

5.5

64.7 mm.

Play

Time

STARBI.

Dot bead

Continue after stop

Analog output 1

Analog output 2

0.0 mm.

Product 0

STARBI.

100

m/min

voltio

0.0

Product 0

Analog output 1

A- If during the execution of a

product the production line

stops (READY status) it is

possible to choose when

the situation is restored,

continue executing the pattern,

continuing from the point where

it stopped, or cancel the current

pattern and wait for a new

product.

B- Machine speed with which you

want to associate an output

voltage value of between 0 and

10 V.

C- Output voltage of the analogue

signal associated with a certain

machine speed.

Содержание STARBI










































































Результаты поиска

Содержание STARBI

Отзывы:

Meler STARBI, Инструкция по эксплуатации, Страница: 49 / 73

Результаты поиска

Содержание STARBI

Отзывы: