background image

9

Control unit MGC mTripod

Notices on the document

Notes and recommendations

IMPORTANT!
The signal word IMPORTANT highlights useful notes and 

recommendations as well as information for an efficient and 

trouble-free operation.

1.3 

Target group

1.3.1 

Personnel – activities and qualifications

All work on the control unit may only be carried out by technicians and 

Magnetic MHTM™ FlowMotion® service experts with the following 

qualifications.

Designation

Qualification

Technician

 ›

Has completed training as a systems mechanic, 

machinery technician, installation mechanic, installation 

technician or has comparable technical training.

 ›

Has completed training as an electrical safety expert. 

 ›

Has additional knowledge and experience.

 ›

Knows the relevant technical terms and regulations.

 ›

Can evaluate the work assigned to him, recognise 

possible dangers and take appropriate safety measures.

Magnetic MHTM™ FlowMotion®  

service expert

 ›

Meets all the requirements of the technician.

 ›

Trained and authorised by Magnetic.

Table 2: 

Qualification of the personnel – control unit MGC

Содержание mTripod





























































































Отзывы: