manualshive.com logo in svg

Magnetic mTripod, Руководство пользователя

Магнитный мТрипод - компактный и удобный тренога для смартфонов с магнитным креплением. Легко устанавливается и удобно переносится. Бесплатно загрузите инструкцию по эксплуатации на manualshive.com, чтобы максимально эффективно использовать этот продукт.

Поделиться
Скачать
background image

17

Control unit MGC mTripod

Digital inputs, digital outputs and relay outputs

2.4 

Illumination

You can order the mTripod turnstile with the following optional illuminations:

 ›

Floor illumination

 ›

Frame illumination

2.4.1 

Floor illumination

For turnstiles with optional floor illumination, the floor illumination is 

connected to the output of the MFM01 plug-in module slot 2, OUT 3 by 

default.
You can switch the floor illumination on and off via the "Illumination off" input 

function.

2.4.2 

Frame illumination

For turnstiles with optional frame illumination, the frame illumination is 

connected to the outputs of the MFM01 plug-in modules slot 2, OUT 1 and 

OUT 2 and slot 3, OUT 1 and OUT 2 by default.
You can switch the frame illumination on and off via the "Illumination off" 

input function.
The following conditions are signalled via the frame illumination:

Frame 

illumination 

left (slot 3)

Frame 

illumination 

right (slot 2)

Description

Red

Red

 ›

The passage is blocked. Input function "Inhibit 

opening" activated.

Flashing red

Flashing red

 ›

An obstacle has been detected.

 ›

Vandalism or fraud detected.

 ›

An error is present.

Green

Green

 ›

Either no validations are pending or the passage 

is free in both passage directions.

Red

Green

 ›

Passage from right to left expected or active.

Green

Red

 ›

Passage from left to right expected or active.

Flashing yellow Flashing yellow

 ›

The pedestrian gate performs homing.

 ›

The home position is being aligned.

Table 8: 

Frame illumination signalling

Содержание mTripod





























































































Отзывы:

Нет отзывов

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Загрузить еще бренды