Magnetic mTripod Скачать руководство пользователя

Страница: 73 / 92

Control unit MGC mTripod

Corrective action

8.6

Event, warning and error messages (troubleshooting)

8.6.1

Event, warning and error messages – Logic control (control unit)

Number

Designation

Possible cause

Corrective action

3120
ERROR

Mains power failure

Short-term power

failure detected.

Check supply voltage and

mains quality.

5112
WARNING

24 V logic voltage too

low

Under voltage

›

Reduce load.

›

Check mains unit.

5530
ERROR

EEPROM checksum

Checksum of

parameters not correct.

›

Reset parameters to

factory settings.

Page

60, chapter 6.10.

6000
ERROR

Module SW-update

failed

Firmware update was

not performed correctly.

›

Restart the control unit.

›

If the error remains,

perform the update again

via the service module.

6101
ERROR

Software error: VS

Software error

›

Perform software update.

6102
ERROR

Software error: System

bus

Within the control, an

error is pending in

communication.

›

Check SW versions of all

plug-in modules. If

necessary, update via the

service module.

›

If all FW versions are up to

date, contact service.

6103
WARNING

FW defaults restored

After a software update.

›

Perform reset.

Page

81, chapter 8.7.

›

If the error occurs

repeatedly, replace the

control unit MGC.

6104
WARNING

Unexpected motor state Motor control error

›

Perform reset.

Page

81, chapter 8.7.

›

Perform software update.

›

Check wiring.

6105
ERROR

Homing failed

The pedestrian gate

could not execute a

reference run.

›

Check motor

communication.

›

Check mechanics.

›

Check the homing sensor.

›

Perform reset.

Page

81, chapter 8.7.

Содержание mTripod





























































































Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Magnetic mTripod, Руководство пользователя

Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды