manualshive.com logo in svg

Magnetic mTripod, Руководство пользователя

Магнитный мТрипод - компактный и удобный тренога для смартфонов с магнитным креплением. Легко устанавливается и удобно переносится. Бесплатно загрузите инструкцию по эксплуатации на manualshive.com, чтобы максимально эффективно использовать этот продукт.

Поделиться
Скачать
background image

58

Control unit MGC mTripod

Description of menus and parameters

6.7 

"Information" menu

Operational view > Main menu > Information

Parameter

Description

Serial no

Displays the serial number of the control unit

Hardware version

Displays the present hardware version

Software #

Displays the present software number

SW version

Displays the present software version

Temperature

Displays the current temperature in the control unit

Logic voltage

Display of the logic voltage, from hardware version E

X20-EN

Display of the analogue voltage 0–10 V at the terminal "X20-EN", from 

hardware version E onwards

PSU-FB

Feedback signal of the mains unit (for future expansions), from hardware 

version E onwards

Table 31: 

Information

6.8 

"Motor MHP2" menu

This menu is displayed for mTripod pedestrian gates with an MHP2 motor.

Operating view > Main menu > Motor MHP2

Parameter

Description

Motor temperature Display of the current motor temperature.
Information

Display of information about the "MHP2 Motor" module: Serial number, 

hardware version, software # and software version.

Table 32: 

Motor MHP2

Содержание mTripod





























































































Отзывы:

Нет отзывов

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Загрузить еще бренды