Magnetic mTripod Скачать руководство пользователя

Страница: 74 / 92

Control unit MGC mTripod

Corrective action

Number

Designation

Possible cause

Corrective action

6110
ERROR

Safety Controller: SW

update required

MHP2 motor detected.

A software package with

the firmware Motor GW

is installed in the control

unit.

Perform the software update

as follows:

›

Execute package PREPARE_

MHP2.

›

Install the latest firmware

package for pedestrian

gates SMP-MGC-PA0.

6111
ERROR

Motor GW: SW update

required

No motor detected.

Firmware Motor GW is

required for the

selected product.

›

Check setting for gate

type.

Perform the software update

as follows:

›

Execute package PREPARE_

MHP1.

›

Install the latest firmware

package for pedestrian

gates SMP-MGC-PA0.

6130
ERROR

Safety Controller:

Configuration faulty

The configuration of the

safety controller is not

consistent.

›

Reset parameters to

factory settings.

Page

60, chapter 6.10.

7530
WARNING

Motor MPH2:

Communication faulty

›

No motor connected.

›

Cables and / or plugs

to the motor

interrupted.

›

Power supply to the

motor interrupted.

›

Check connections.

›

Check CAN termination

and correct if necessary.

See separate electrical

wiring diagram.

8130
WARNING

Node monitoring

The communication to a

plug-in module was

interrupted.

›

Check whether all plug-in

modules are listed in the

main menu.

›

Perform reset.

Page

81, chapter 8.7.

FF20
WARNING

Emergency open active 0 V or no signal is

present at the

"Emergency open"

input.

›

Check input signal.

›

If not used, deactivate the

input function.

FF21
WARNING

Max. pulses without

passage reached

The set maximum

number of pulses

without passage has

been reached.

›

Check card reader /

validation device, e.g. card

reader.

›

Check the "Max pulse w/o

passage" parameter.

Page 48, chapter

6.2.5.

Содержание mTripod





























































































Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Magnetic mTripod, Руководство пользователя

Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды