MacDon R1 FR Series Скачать руководство пользователя страница 222

Страница: 222 / 238

262391

210

Revision A

Problem

Solution

Refer to

Symptom: Breakage of conditioner drive belt

Improper belt tension

Adjust conditioner drive belt tension.

4.5.5 Conditioner Drive Belt, page 182

Belt not in proper groove in pulley

Move belt to proper groove.

4.5.5 Conditioner Drive Belt, page 182

Foreign object between rolls

Disengage rotary disc header and stop
engine. When all moving parts have
completely stopped, remove foreign
object.

3.16 Unplugging Rotary Disc Header,
page 65

Belt pulleys and idlers misaligned

Align pulleys and idler.

4.5.5 Conditioner Drive Belt, page 182

Symptom: Machine pulling to one side

Rotary disc header dragging on one
end and pulling to that side

Adjust rotary disc header float on
both ends.

3.13.2 Float, page 43

Symptom: Disc does not start when engaging power take-off (PTO)

Mud on cutterbar

Remove mud from cutterbar. Do not
allow mud to dry on cutterbar.

3.16 Unplugging Rotary Disc Header,
page 65

Primary driveline not connected

Connect driveline.

Installing Primary Driveline, page 178

Cross driveline not connected

Connect driveline.

Installing Cross Driveline, page 180

Symptom: Header does not raise properly

Auxiliary lift locking pins installed.

Remove auxiliary lift locking pins
before attempting to raise header.

3.1.2 Removing Auxiliary Lift Locking
Pins, page 20

Hydraulic flow setting from tractor to
auxiliary lift cylinder valve too high

Set the hydraulic flow rate from the
tractor front selective control valve to
15

–

20 %.

For instructions, refer to the tractor
operator

’

s manual.

Header position sensor(s) misaligned

Adjust the header position sensors.

4.7.3 Inspecting Auxiliary Lift System
Sensors, page 199

Header position sensor(s) damaged

Replace damaged sensors.

Contact your MacDon dealer.

Relay logic switch is set to OFF or
MANUAL.

Set relay logic switch to AUTO.

4.7.4 Setting Relay Logic Switch, page
201

TROUBLESHOOTING

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды