MacDon R1 FR Series Скачать руководство пользователя страница 170

Страница: 170 / 238

262391

158

Revision A

1011147

Figure 4.141: Hub Drive to Driveline Connection

Lubricate spindle splines (A). For specifications, refer to the
inside back cover of this manual.

NOTE:

The driveline U-joints were greased at the factory and are
considered to be lubricated for life. No further lubrication is
required.

NOTE:

The illustration shows a cutaway view of the drum and the
tube shield.

Insert driveline (B) at an angle and guide it past hub
drive (C) and drum (D).

Insert splined spindle end (A) into the splined bore on
driveline (B).

1011137

Figure 4.142: Hub Drive to Driveline Connection

10. Place a bead of medium-strength threadlocker (Loctite

243

or equivalent) around the threads of four M12 hex flange
head bolts (A). Use the bolts and spacers to secure driveline
assembly (B) to hub drive (C). Torque the bolts to 102 Nm
(75 lbf·ft).

1011136

Figure 4.143: Drum Shield

11. Position two drum shields (B) as shown. Apply a bead of

medium-strength threadlocker (Loctite

243 or equivalent)

around the threads of eight M8 hex flange head bolts (A).
Use the bolts to secure the drum shields. Torque the bolts
to 27 Nm (239 lbf in).

MAINTENANCE AND SERVICING

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды