MacDon R1 FR Series Скачать руководство пользователя страница 180

Страница: 180 / 238

262391

168

Revision A

If the rotary disc header is raised:

Place blocks under each end, or just inside each end, of the cutterbar.

Lower the rotary disc header onto the blocks.

Shut down the engine, and remove the key from the ignition.

Close the auxiliary lift cylinder lock-out valves. For instructions, refer to

3.2.1 Locking and Unlocking Auxiliary Lift

Cylinders, page 22

1016458

Figure 4.161: Cutterbar Spindle

Fill the space above the bearing with grease.

Place hub (A) on spindle (C).

Install shear pins (B) so that both shear pin grooves are
parallel to the cutterbar.

NOTE:

Ensure that the ends of shear pins (B) do not protrude past
the step in hub (A).

1011150

Figure 4.162: Shear Pin Orientation

Observe the orientation of the grooves in shear pins (A).

IMPORTANT:

Correct shear pin orientation is critical. Both shear pin
grooves (A) must be parallel to the cutterbar. They do not
need to be facing in the same direction.

NOTE:

The shaft has been removed from the illustration for clarity.

MAINTENANCE AND SERVICING

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды