MacDon R1 FR Series Скачать руководство пользователя страница 183

Страница: 183 / 238

262391

171

Revision A

4.5

Drive Systems

4.5.1

Driveshields

Driveshields protect people from rotating belts and drives.

Removing Driveshields

No additional tools are needed to remove the driveshields.

WARNING

To reduce the risk of personal injury, do NOT operate the machine without the driveshields in place and secured.

ϭϬϰϯϲϬϴ

Figure 4.168: Left Driveshield

NOTE:

The illustrations shown in this procedure depict the left
driveshield (A); the right driveshield is similar.

1010707

Figure 4.169: Tool to Unlock Driveshield

Remove lynch pin (A) and tool (B) from pin (C).

MAINTENANCE AND SERVICING

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды