MacDon R1 FR Series Скачать руководство пользователя страница 124

Страница: 124 / 238

262391

112

Revision A

1019153

Figure 4.60: Cutterbar Spindles

IMPORTANT:

•

Spindles that rotate clockwise have right-leading threading
and are identified by a smooth top on spindle gear shaft (A).

•

Spindles that rotate counterclockwise have left-leading
threading and are identified by machined grooves on spindle
gear shaft (B) and nut (C).

•

If the spindle position in the cutterbar has changed, the
rotational direction of that spindle

MUST

remain the same

(that is, a clockwise spindle must maintain its clockwise
rotation).

•

Failure to maintain the rotation pattern can result in damage
to the spindle and/or to the cutterbar components.

•

The shear pin will not perform properly if the spindles used
are in the wrong orientation.

Changing Eight Disc Cutterbar Crop Stream Configuration

Two crop stream settings are possible: one stream and three streams.

Figure 4.61: Spindle Rotation Pattern and Crop Streams (8 Disc)

1021828

A - One Crop Stream

B - Three Crop Streams

To change (8 disc) spindle rotation from three crop streams (B) to one crop stream (A):

•

Swap disc/spindle (3) with disc/spindle (6)

To change (8 disc) spindle rotation from one crop stream (A) to three crop streams (B):

•

Swap disc/spindle (6) with disc/spindle (3)

For instructions, refer to

Removing Cutterbar Spindles, page 102

and

Installing Cutterbar Spindles, page 105

MAINTENANCE AND SERVICING

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды