MacDon R1 FR Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 238

background image

262391

30

Revision A

3.7

Attaching Rotary Disc Header to Tractor

The rotary disc header can be attached to the tractor with a 3-point hitch.

3.7.1

Connecting the Tractor to the Rotary Disc Header

Connecting the header to the tractor involves connecting the hydraulic and electrical systems. The R1 FR Series can attach
to 3-point hitch categories 2, 3, and 3N.

DANGER

To prevent bodily injury or death from the unexpected startup of the machine, always stop the engine and remove the
key from the ignition before leaving the operator

’

s seat.

DANGER

Ensure that all bystanders have cleared the area.

1.

Ensure the machine is set on a flat level surface.

ϭϬϰϯϲϮϭ

A

B

E

F

C

D

Figure 3.14: Front Linkage Connections

2.

Connect your tractor

’

s 3-point hitch to the following

locations on the header frame according to the hitch type.

•

Category 3: connect to upper linkage (A) and lower
linkages (D).

•

Category 3N: connect to upper linkage (A) and lower
linkages (C).

•

Category 2: connect upper linkage (B) and lower
linkages (C).

ϭϬϰϯϱϲϴ

B

C

A

D

E

B

Figure 3.15: Alignment with Header Carrier Frame

3.

Attach 3-point hitch (A) to carrier frame linkage (B). Refer
to your tractor hitch instructions to properly secure the
connections.

4.

Lower the header fully.

5.

Shut down the engine, and remove the key from the
ignition.

«
...
40
41
42
43
44
...
»

Содержание R1 FR Series















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 FR Series

Бренд: Makita Страницы: 17

Бренд: Makita Страницы: 13

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Backyard Play Systems Страницы: 64

Бренд: Haenim Страницы: 2

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: Dairyland Страницы: 21

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Eastern Jungle Gym Страницы: 17

Бренд: Vahle Страницы: 96

Бренд: CAMPAGNOLA Страницы: 4

Бренд: Nederman Страницы: 255

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды