LS 47200001 Скачать руководство пользователя страница 33

Страница: 33 / 200

Chapter 3 Installation and Test Operation

3-6

3.4 Test Operation

Terminal resistance switch of Pnet cable shall be On. If the switch is not On, communication errors may

occur. Check LED operation status if normal with power on after communication cable is connected. If

normal, download the applicable program to PLC via XG5000 so to execute the program.

3.4.1 Precautions for system configuration

1) Station No. of each slave shall be surely different from each other including this module. If connected

with the repeated station No., communication error may occur, leading to communication trouble.

High-speed link station No. of all stations also shall be different from each other to use High-speed

link service.

2) Use the communication cable as specified only. If not, serious error may occur to communication.

3) Check communication cable if disconnected or shorted prior to installation.

4) Tighten up communication cable connector until connected firmly. If cable connection is unstable, serious

error may occur to communication.

5) If remote communication cable is connected, keep the cable far away from power line or inductive noise.

6) Since the coaxial cable is not flexible, it is to be diverged min. 30cm away from the connector in

communication module. If the cable is bent at a right angle or transformed compulsorily, cable

disconnection or connector damage in communication module will be caused.

7) If LED operation is abnormal, refer to Chapter 10 Troubleshooting to check for causes and take actions

against. Contact service center if the error is as before.

Содержание 47200001









































































































































































































Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды

LS 47200001, Руководство пользователя

Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды