LS 47200001 Скачать руководство пользователя страница 19

Страница: 19 / 200

Chapter 1 Introduction

1-4

1.4 Software

This describes on the software tool for the Pnet I/F module. For programming and application, refer to the
followings

1.4.1 Check list for the software

(1) Software list

Item

Programming tool

Communication

configuration tool

XGL-PMEA/

XGL-PMEC/

XGL-PMEB

Profibus-DP master module

XG5000

(2) Selecting the CPU (Version) to use the Pnet I/F module

Item

Model

Available version

(recommended)

Remark

XGK series

XGK-CPUH

V2.0

XGK-CPUS

V2.0

XGK-CPUA

V2.0

XGK-CPUE

V2.0

XGK-CPUU

V1.0

XGI series

XGI-CPUH

V1.0

XGI-CPUU

V1.0

XGR series

XGR-CPUH/T

V1.0

XGR-XPUH/F

V1.0

Software

XG5000

V4.2

SyCon

V2.0

Configuration tool for XGL-PMEA

N Configurator

V3.1.0.2

Configuration tool for XGL-PMEB/C

Note

(1) You can download the above software from our web site. In case Internet is available, visit the

nearest distributor and get the installation CD.

Web site address:

http://www.lselectric.co.kr/

(2) You can program the XG5000 through the RS-232C port and USB of the CPU module. For the

cable, refer to wiring diagram of the CPU module.

(3) You can configure the network system by SyCon through the

“Config” port of the XGL-PMEA.

Only 9-pin serial port is available and simultaneous connection with XG5000 is not available.

(4) You can set the parameter by N Configurator for XGL-PMEB/C through the USB port of the CPU

module and connection with XG5000 is available.

(5) In case you use the product other than available version, some function may not work properly. If

possible, use the recommended version and check the compatibility.

Содержание 47200001









































































































































































































Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды

LS 47200001, Руководство пользователя

Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды