LS 47200001 Скачать руководство пользователя страница 109

Страница: 109 / 200

Chapter 8 High-speed Link

8-10

8.5 High-speed Link Information

With High-speed link service used to exchange data between communication modules of two or more

stations, it provides a checking method of High-speed link service status for the user through High-speed

link information so to confirm reliability of the data read from the destination station via the High-speed link.

In other words, the communication module synthesizes the data received up to that time at intervals of a

specific time and lets the user know if High-speed link operates as in parameters specified by the user

through High-speed link information where the whole information of Run-link(_HSxRLINK) and Link-

trouble(_HSxLTRBL) to provide the whole information of the communication network, and the individual

information of _HSxSTATE, _HSxTRX, _HSxMOD and _HSxERR to provide communication status for

128 register items in the parameters are contained.

The user can use the information in keyword format when programming, and also monitor the High-speed

link status using the monitor function of the High-speed link information. Prior to its application, the user is

requested to check the reliability of the Send/Receive data through High-speed link information of Run-link

and Link-trouble when operating several PLCs with High-speed link used.

[Table 8.5.1] below shows functions and definition of the High-speed link information.

Classification

Run-link

Link-trouble

Send/Receive

status

Operation

Mode

Error

High-speed

link status

Information type

Whole

information

Whole

information

Individual

information

Individual

information

Individual

information

Individual

information

Keyword name

(x=High-speed link no.

n=station no.)

_HSxRLINK _HSxLTRBL

_HSxTRX[n]

(n=0.127)

_HSxMOD[n]

(n=0.127)

_HSxERR[n]

(n=0.127)

_HSxSTATE[n

](n=0.127)

Data type

Bit

Bit-Array

Monitor

Available

Program

Available

[Table 8.5.1] High-speed link information function

[Figure 8.5.1] Monitor window of variables

Содержание 47200001









































































































































































































Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды

LS 47200001, Руководство пользователя

Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды