LS 47200001 Скачать руководство пользователя страница 28

Страница: 28 / 200

Chapter 3 Installation and Test Operation

3-1

Chapter 3 Installation and Test Operation

3.1 Precautions for Installation

3.1.1 Precautions for Installation

For system configuration through Pnet I/F module, carefully make sure of the following items prior to
installation.

1) Check the basic factors necessary for system configuration to select an appropriate communication

module.

2) Select the exclusive Pnet cable to be used for this communication module.

3) Before the communication module is installed, check for any foreign material on the base connector the

module will be installed on and any damage on the connector pin of the module.

4) All the communication modules can be installed on the basic base ~ the expansion base. For the

number of available expansion base by CPU, refer to the following table.

Item

XGK

XGI

XGR

XGK-

CPUH

/CPUU

XGK-

CPUA

/CPUS

/CPUSN

XGK-

CPUHN

/CPUUN

XGK-

CPUE

XGI-

CPUUN

XGI-

CPUU

XGI-

CPUH

XGI-

CPUS

XGI-

CPUE

XGR-

CPUH/T,
CPUH/F,

CPUH/S

Number of

available

expansion base

(max.)

(Available to

equip

communication

module)

5) For installation of the module, exactly insert the protuberant part at the bottom of the module with the

communication cable disconnected into the base groove and then apply enough strength until its top is
locked up with the locking device of the base. If the lock is not applied, it may cause an error on the
interface with CPU.

Содержание 47200001









































































































































































































Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды

LS 47200001, Руководство пользователя

Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды