LS 47200001 Скачать руководство пользователя страница 29

Страница: 29 / 200

Chapter 3 Installation and Test Operation

3-2

3.2 From Setting to Operation

The sequence of the product from installation to operation will be described below. After the product

installation is complete, install and configure the system to be operated as specified in the following

sequence.

Operation Sequence



Install Pnet I/F module on the base.



Check the applicable base/slot position for correct installation.



Configure the system between Pnet I/F module and slaves.



Use the exclusive Pnet cable for communication.



Set each slave

’s station number



With power On, check the LED status of the communication module.



Check if the interface of the communication module is normal with CPU.(RUN: On, I/F: Blink, ERR:

Off)



Specify the configuration through SyCon or N Configurator.



Specify the module to be configured as Pnet I/F master module and download it.



Download High-speed link/P2P parameters.



Set how to connection with [Online]

– [Connection]



[Online]

– [Diagnosis] – [I/O information] – [I/O Sync.]



Open the [High-speed Link] block setting tab



Execute [Online]

– [Communication module setting] – [Config. Upload] at [High-speed Link] block tab



Set the High-speed Link block parameters



Download the parameters with [Online]

– [Write]



Execute [Online]

– [Communication module setting] – [Enable Link]



Open [P2P] block setting tab



Set the P2P block parameters



Download the parameters with [Online]

– [Write]



Execute [Online]

– [Communication module setting] – [Enable Link]



Use system diagnosis function in XG5000 to check the normal operation of the product.



Set how to connection with [Online]

– [Connection]



Execute [Online]

– [Communication module setting] – [System Diagnosis]



Open the [Status by service] window in [System Diagnosis]



Check the normal operation with P2P and High-speed Link service



Start Run

Содержание 47200001









































































































































































































Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды

LS 47200001, Руководство пользователя

Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды