LS 47200001 Скачать руководство пользователя страница 32

Страница: 32 / 200

Chapter 3 Installation and Test Operation

3-5

3) Pnet termination

- Connector

4) General notices

(1) Termination treatment of vertical section is needed.

(2) In case that the distance is far between stations, it is possible to extend the segment through

repeater(max. 9 repeater, 10 segment), available to connect 32 stations per segment(include

repeater), max. 126 stations. (Repeater does not have station no.) The extended segment

having no station is available.

(3) Shield shall be connected to the housing of connector.

(4) Use the special connector having the inductor inside.

(5) Spur Line is not allowed to use.

(6) If the ground potential difference between stations is big, a great amount of current may flow

through the shield. In this case, install the cable to make the ground potential difference equal

separately. For high speed more than 1.5Mbps, special cares should be taken.

(7) In case of 12Mbps, keep the distance more than 1m between stations.

5) Termination treatment

(1) Each segment should do the termination treatment for both ends. If there are several segments,

it is required to do the termination treatment for each segment.

(2) Termination is available to turn on/off by the switch of special connector.

(3) If possible, install the master at the end of one side.

Содержание 47200001









































































































































































































Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды

LS 47200001, Руководство пользователя

Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды