LS 47200001 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 200

background image

Chapter 12 Compliance with EMC Specifications

12-1

Chapter 12 Compliance with EMC Specifications

12.1 Requirements Complying with EMC Specifications

EMC Directions describe

“Do not emit strong electromagnetic wave to the outside: Emission” and “Do not have an

influence of electromagnetic wave from the outside: Immunity

”, and the applicable products are requested to meet

the  directions.  The  chapter  summarizes  how  to  structure  a  system  using  XGT  PLC  to  comply  with  the  EMC
directions.  The  description  is  the  data  summarized  for  the  requirements  and  specifications  of  EMC  regulation
acquired by the company but it does not mean that every system manufactured according to the description meets
the  following  specifications.  The  method  and  determination  to  comply  with  the  EMC  directions  should  be  finally
determined by the system manufacturer self.

12.1.1 EMC specifications

The EMC specifications affecting the PLC are as follows.

Specification

Test items

Test details

Standard value

EN50081-2

EN55011 Radiated
noise

＊

2

Measure the wave emitted from a
product.

30~230

㎒

QP : 50

㏈㎶

/m

＊

1

230~1000

㎒

QP : 57

㏈㎶

/m

EN55011 conducted
noise

Measure the noise that a product emits
to the power line.

150~500

㎑

QP : 79

㏈

Mean : 66

㏈

500~230

㎒

QP : 73

㏈

Mean : 60

㏈

EN61131-2

EN61000-4-
Electrostatic
immunity

Immunity test allowing static electricity to
the case of a device.

15

㎸

Air discharge

8

㎸

Contact discharge

EN61000-4-4
Fast transient burst
noise

Immunity test allowing a fast noise to
power cable and signal cable.

Power line : 2

㎸

Digital I/O : 1

㎸

Analogue I/O, signal lines : 1

㎸

EN61000-4-3
Radiated field AM
modulation

Immunity test injecting electric field to a
product.

10Vm, 26~1000

㎒

80% AM modulation@ 1

㎑

EN61000-4-12
Damped oscillatory
wave immunity

Immunity test allowing attenuation
vibration wave to power cable.

Power line : 1

㎸

Digital I/O(24V and higher) : 1

㎸

[Table 12.1.1] EMC specification list

＊

1 : QP: Quasi Peak, Mean : average value

＊

2 : PLC is a type of open device(installed on another device) and to be installed in a panel.

For any applicable tests, the system is tested with the system installed in a panel.

«
...
184
185
186
187
188
...
»

Содержание 47200001









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 47200001

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Calsense Страницы: 74

Бренд: LAS Страницы: 6

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Yoshitake Страницы: 4

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: Desoutter Страницы: 74

Бренд: jablotron Страницы: 2

Бренд: Multi-Clean Страницы: 4

Бренд: Primo Water Страницы: 10

Бренд: PENGWYN Страницы: 32

Бренд: Warner Electric Страницы: 6

Бренд: Radionics Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды