LS 47200001 Скачать руководство пользователя страница 75

Страница: 75 / 200

Chapter 7 N Configurator Setting

7-2

7.2 Installation

7.2.1 System requirements



486 PC or higher



More than 16 Mbytes of RAM



Windows 95/98/ME/NT/2000/XP



More than 80 Mbytes of hard disk, CD ROM drive



Resolution: 1280 x 1024 pixel recommended



Windows 95: Service Pack 1 or higher



Windows NT: Service Pack 3 or higher

7.2.2 How to install Program

Please see the software manual of N Configurator for more details. We will discuss the
composition after the installation of the software.

(1) Directory after installation

After the installation, generally, “C:\Program Files\xg5000\nCongirurator” directory is

composed as follows.

[Figure 7.2.1] The structure of installation directory

- N Configurator: Root directory of configuration tool for PROFIBUS DP Master
- bmp:

Bitmap depository used by the GSD file

- bnr:

Network Configuration binary image file depository

- gsd:

GSD file depository provided by the manufacturer of PROFIBUS DP module

- prj:

Network Configuration Project depository

- sys:

Application setting directory used by the tool

(2) Caution after installation

After the installation is completed, users should be aware of following things. The default

GSD files provided are our company

’s smart I/O and inverter, so other companies’

products or new products are not updated. Therefore, if there is a new GSD file, then copy

it to the GSD directory to use, and copy bitmap image files used by the GSD to the bmp

directory. Start again the N Configurator program to apply the copied GSD.

Содержание 47200001









































































































































































































Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды

LS 47200001, Руководство пользователя

Результаты поиска

Содержание 47200001

Отзывы:

Похожие инструкции для 47200001

Бренды по названию

Популярные бренды