LG A005KEEN261 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 74

background image

66

Appendix

Appendix

4

FCC compliance information

[USA]

FCC Notice

The following notice covers the transmitter module contained in this product.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

-

Reorient or relocate the receiving antenna.

-

Increase the separation between the equipment and the receiver.

-

Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.

-

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference; and
2) this device must accept any interference received, including interference that may cause

undesired operation of the device.

Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm

between the radiator and your body. End users must follow the specific operating instructions

for satisfying RF exposure compliance.This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

«
...
64
65
66
67
68
...
»

Содержание A005KEEN261











































































Отзывы:

Нет отзывов

Похожие инструкции для A005KEEN261

Бренд: Baldor Страницы: 55

MaitreView 4KLite

Бренд: AVLink Страницы: 10

CIMR-XC2 Series

Бренд: YASKAWA Страницы: 77

Бренд: Roland Страницы: 6

Бренд: APS Страницы: 70

Бренд: Wacker Neuson Страницы: 36

Бренд: Baja Silueta Страницы: 99

Бренд: Delta Electronics Страницы: 2

CONSONANCE REFERENCE DB1

Бренд: Opera Страницы: 3

INTERNATIONAL TRAVEL ADAPTER

Бренд: Igo Страницы: 1

Бренд: Ace Plus Страницы: 9

Dazzle Digital Video Creator 90

Бренд: Pinnacle Systems Страницы: 53

Бренд: Starview Страницы: 6

Бренд: Pro-Ject Audio Systems Страницы: 3

Бренд: IONODES Страницы: 23

COMBIVERT F4-S Series

Бренд: KEB Страницы: 30

Бренд: ZeeVee Страницы: 7

Бренд: ICP DAS USA Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды