LG A005KEEN261 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 74

background image

61

Appendix

Appendix

4

LGE Open Source Software Notice

This product from LG Electronics, Inc. (“LGE”) contains the open source software detailed below.
Please refer to the indicated open source licenses (which are included following this notice) for the
terms and conditions of their use.

Open Source

License

Copyright

FreeRTOS 8.1.2

FreeRTOS License

Copyright (c) 2014 Real Time Engineers Ltd

The source code for the above may be obtained free of charge from LGE at
http://opensource.lge.com. LGE will also provide open source code to you on a CD-ROM for a charge
covering the cost of performing such distribution (such as the cost of media, shipping, and handling)
upon email request to [email protected]. This offer is valid for a period of three years after our
last shipment of this product. This offer is valid to anyone in receipt of this information.
Please be informed that this LG Electronics, Inc. product may contain open source software listed in
the tables below.

Open Source

License

Copyright

cJSON 1.6.0

MIT

Copyright (c) 2009-2017 Dave Gamble and cJSON
contributors

FatFS 0.12

FatFS License

Copyright (C) 2016, ChaN

lwIP 2.0.0

BSD-3-Clause

Copyright (c) 2001, 2002 Swedish Institute of
Computer Science.

mbed TLS 2.4.0

Apache-2.0

Copyright (c) 2006-2016, ARM Limited

sds 2.0.0

BSD-2-Clause-NetBSD

Copyright (c) 2006-2014, Salvatore Sanfilippo

<antirez at gmail dot com>

License URLs

y

Apache-2.0 : http://opensource.lge.com/license/Apache-2.0.html

y

BSD-2-Clause-NetBSD : http://opensource.lge.com/license/BSD-2-Clause-NetBSD.html

y

BSD-3-Clause : http://opensource.lge.com/license/BSD-3-Clause.html

y

FatFS License : http://opensource.lge.com/license/FatFS_License.html

y

FreeRTOS License : http://opensource.lge.com/license/FreeRTOS_License.html

y

MIT : http://opensource.lge.com/license/MIT.html

«
...
59
60
61
62
63
...
»

Содержание A005KEEN261











































































Отзывы:

Нет отзывов

Похожие инструкции для A005KEEN261

Бренд: Omega Engineering Страницы: 10

Бренд: Parker Страницы: 99

Бренд: SAJ Страницы: 60

Бренд: Konig Страницы: 30

Бренд: K&S BASIC Страницы: 17

Бренд: Midian Страницы: 28

Бренд: 3onedata Страницы: 7

Бренд: Cable-Tronix Страницы: 4

Бренд: Waversasystems Страницы: 15

L.O.C.PRO LP7-2

Бренд: PAC Страницы: 2

Бренд: Solplanet Страницы: 75

Бренд: WORMS Страницы: 52

Бренд: Altera Страницы: 87

Бренд: CTC Union Страницы: 44

Бренд: Patton electronics Страницы: 20

Бренд: Planet Страницы: 28

Бренд: ENFORCER Страницы: 4

SUNNY BOY STORAGE 2.5

Бренд: SMA Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды