Lenovo x3250 m6 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 696

background image

To start using the embedded hypervisor, you must add the USB flash device to the startup sequence in
the Setup Utility.

To add the USB flash device to the startup sequence, do the following:

Step 1.

Turn on the server.

Note:

Approximately 20 seconds after the server is connected to power, the power-control button

becomes active.

Step 2.

When the prompt

<F1> Setup

is displayed, press F1.

Step 3.

From the Setup Utility main menu, select

Boot Manager

.

Step 4.

Select

Add Boot Option

; then, select

Generic Boot Option

➙

Embedded Hypervisor

. Press

Enter, and then press Esc.

Step 5.

Select

Change Boot Order

➙

Change the order

. Use the up and down arrow keys to select

Embedded Hypervisor

and use the plus (+) and minus (-) keys to move Embedded Hypervisor in

the boot order. When

Embedded Hypervisor

is in the correct location in the boot order, press

Enter. Select

Commit Changes

and press Enter.

Step 6.

Select

Save Settings

and then select

Exit Setup

.

If the embedded hypervisor flash device image becomes corrupt, you can download the image from
https://my.vmware.com/web/vmware/downloads.

For more information, see the VMware vSphere Documentation at
http://www.vmware.com/support/pubs/vs_pages/vsp_pubs_esxi41_e_vc41.html or the

VMware vSphere

Installation and Setup Guide

at http://pubs.vmware.com/vsphere-50/topic/com.vmware.ICbase/PDF

/vsphere-esxi-vcenter-server-50-installation-setup-guide.pdf.

Ethernet controller information

The Ethernet controllers are integrated on the system board. They provide an interface for connecting to a 10
Mbps, 100 Mbps, or 1 Gbps network and provide full-duplex (FDX) capability, which enables simultaneous
transmission and reception of data on the network. If the Ethernet connectors in the server support
auto-negotiation, the controllers detect the data-transfer rate (10BASE-T, 100BASE-TX, or 1000BASE-T) and
duplex mode (full-duplex or half-duplex) of the network and automatically operate at that rate and mode.

You do not have to set any jumpers or configure the controllers. However, you must install a device driver to
enable the operating system to address the controllers.

To find device drivers, go to http://www.lenovo.com/support.

Enabling Features on Demand Ethernet and Demand RAID software

You can activate the Features on Demand (FoD) software upgrade key for the following:

• Fibre Channel over Ethernet (FCoE)

• iSCSI storage protocol

• RAID

The FCoE and iSCSI storage protocols and RAID are integrated in the IMM2.

For more information, see the

Lenovo Features on Demand User’s Guide

. To download the document, go to

http://www.ibm.com/systems/x/fod/, log in, and click

Help

.

38

Lenovo System x3250 M6 Installation and Service Guide

«
...
50
51
52
53
54
...
»

Содержание x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3250 m6

5big - Network NAS Server

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 14

Бренд: Xerox Страницы: 8

Бренд: Jung Страницы: 16

UltraNEXUS-HD Flex

Бренд: Leightronix Страницы: 5

Бренд: Interface Masters Страницы: 34

A+ AS -2114GT-DNR

Бренд: Supermicro Страницы: 126

RIP Station 5100

Бренд: Epson Страницы: 140

Бренд: QNAP Страницы: 55

ANTMINER S19 Pro

Бренд: BITMAIN Страницы: 17

Multi-Port Fast Ethernet Print Server FPS-3121

Бренд: Planet Страницы: 57

Бренд: Planet Страницы: 74

Бренд: Planet Страницы: 90

Access Server M

Бренд: SSS Siedle Страницы: 28

Бренд: C-MOR Страницы: 43

Бренд: FreeNAS Страницы: 4

S815EBM1 - Server Board Motherboard

Бренд: Intel Страницы: 76

Бренд: Lantronix Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды