Lenovo x3250 m6 Скачать руководство пользователя страница 187 | Manualshive

Страница: 187 / 696

background image

4. Reconnect the power cords.

5. Update the server configuration.

a. Save the new configuration settings when starting the server for the first time after you add or

remove a device. The Setup Utility program starts automatically.

b. Install device drivers for some optional devices. See the documentation that comes with each device

c. Reconfigure the disk arrays if you have installed or removed an HDD and a RAID adapter. See the

documentation that comes with the RAID adapter

d. Configure the Ethernet controller, see “Ethernet controller information” on page 38.

6. Start the server. Confirm that it starts properly and recognizes the newly installed devices, and make

sure that no error LEDs are lit.

7. For Business Partners only: Complete the additional steps in “Instructions for Business Partners” on

Instructions for Business Partners

This topic provides instructions for Business Partners on verifying the newly installed devices by running
the Dynamic System Analysis (DSA) stress test.

In addition to the instructions in this chapter for installing optional hardware devices, updating firmware and
device drivers, and completing the installation, Business Partners must also do the following:

1. After you have confirmed that the server starts correctly and recognizes the newly installed devices

and that no error LEDs are lit, run the DSA stress test. For information about using DSA, see “Dynamic
System Analysis” on page 58.

2. Shut down and restart the server multiple times to ensure that the server is correctly configured and

functions properly with the newly installed devices.

3. Save the DSA log as a file and send it to Lenovo. See “Sending DSA data to Lenovo” on page 173.

4. To ship the server, repackage it in the original undamaged packing material and observe Lenovo

procedures for shipping.

Support information for Business Partners is available at http://www.ibm.com/partnerworld.

Sending DSA data to Lenovo

Before you send DSA data to Lenovo, read the terms of use at:
http://www.ibm.com/de/support/ecurep/terms.html

You can use any of the following methods to send the DSA data to Lenovo:

•

Standard upload

:

http://www.ibm.com/de/support/ecurep/send_http.html

•

Standard upload with the system serial number

:

http://www.ecurep.ibm.com/app/upload_hw

•

Secure upload

:

http://www.ibm.com/de/support/ecurep/send_http.html#secure

•

Secure upload with the system serial number

:

https://www.ecurep.ibm.com/app/upload_hw

Removing and installing server components

173

«
...
185
186
187
188
189
...
»

Содержание x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3250 m6

Бренд: D-Link Страницы: 38

Epress EtherNetwork DP-301P+

Бренд: D-Link Страницы: 2

Бренд: AIC Страницы: 52

MCX-2000 - MusicCAST Digital Audio Server

Бренд: Yamaha Страницы: 25

UniServer R6900 G5

Бренд: H3C Страницы: 17

Бренд: Edimax Страницы: 93

Бренд: Novell Страницы: 152

SCHROFF 11850-016

Бренд: nvent Страницы: 18

SUPERSERVER 6035B-8R+

Бренд: Supero Страницы: 110

Бренд: Raritan Страницы: 99

301P - DP Print Server

Бренд: D-Link Страницы: 150

Бренд: SpectraLink Страницы: 31

WPS870G - Wireless Print Server

Бренд: Motorola Страницы: 115

Бренд: ASUSTOR Страницы: 12

Бренд: DATONG Страницы: 23

Бренд: Kramer Страницы: 72

Бренд: Obvius Страницы: 39

Бренд: Lantronix Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды