Lenovo x3250 m6 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 696

background image

Step 1.

Carefully lower the backplate assembly into the alignment slots in the chassis. Then, close the
retention latches to secure the backplate assembly to the chassis.

Figure 83. 3.5-inch simple-swap hard-disk-drive backplate assembly installation

Step 2.

Connect cables to the RAID adapter or system board. Refer to the following topics:

•

“Simple-swap HDD cable connection: onboard RAID” on page 162

•

“Simple-swap HDD cable connection: ServeRAID SAS/SATA controller and redundant power

supply” on page 170

•

“Simple-swap HDD cable connection: ServeRAID SAS/SATA controller and fixed power

supply” on page 166

Step 3.

Install the hard disk drives and fillers. See “Installing a simple-swap hard disk drive” on page 105.

Step 4.

Complete the parts replacement. See “Completing the parts replacement” on page 172.

Removing and installing Tier 2 CRUs

This section provides information about removing and installing Tier 2 CRUs.

You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the
type of warranty service that is designated for your server. The illustrations in this document might differ
slightly from your hardware.

Removing the microprocessor and heat sink (Trained technician only)

The following notes describe the type of microprocessor that the server supports and other information that
you must consider when you install or remove a microprocessor and heat sink:

• The server supports one Intel land grid array (LGA) 1151 dual-core or quad-core microprocessor. The

type, speed, and L3 cache of the microprocessor depends on the server model.

• Read the documentation that comes with the microprocessor to determine whether you have

to update the server firmware. To download the most current level of server firmware, go to
http://www.lenovo.com/support and http://www.ibm.com/support/fixcentral.

Removing and installing server components

145

«
...
157
158
159
160
161
...
»

Содержание x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3250 m6

Univerge SV8100

Бренд: NEC Страницы: 78

Univerge SV8100

Бренд: NEC Страницы: 186

Univerge SV8100

Бренд: NEC Страницы: 150

Univerge SV8100

Бренд: NEC Страницы: 52

Бренд: Zonet Страницы: 33

ioLogik W5300 Series

Бренд: Moxa Technologies Страницы: 177

Бренд: AIC Страницы: 112

Бренд: QNAP Страницы: 44

WSG SoundGrid Server One

Бренд: Waves Страницы: 4

Бренд: Xerox Страницы: 13

6100BD - Phaser Color Laser Printer

Бренд: Xerox Страницы: 34

6100BD - Phaser Color Laser Printer

Бренд: Xerox Страницы: 140

ANTMINER S19 Pro

Бренд: BITMAIN Страницы: 17

Бренд: Viavi Страницы: 11

Бренд: Planet Страницы: 87

Xtreme PC NG6452

Бренд: Chip PC Страницы: 4

RASFinder RF300E

Бренд: Multitech Страницы: 199

Бренд: Pepperl+Fuchs Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды