Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 49

Страница: 49 / 110

Chapter 3: Installing NE0152T Hardware and Options

Secure the air-duct mounting bracket to the rails with M6 screws. Torque the
screws to approximately 5.7 Nm ± 0.1 Nm (50 inch-pounds).

Note:

Reuse the original M6 screws used to fasten the 4-post rack mounting

brackets to secure the air duct mounting brackets with 4-post mounting brackets
together.

Secure the air-duct mounting bracket to the rack chassis with M3.5 screws. Torque
the screws to approximately 1.1 Nm ± 0.1 Nm (10 inch-pounds).

Plug the power cords into their respective NE0152T power connectors and using tie
wraps, secure the power cords to the mounting rails.

M3.5 screws

Air duct mounting bracket

M6 screws

Tie wraps

Power connection

Содержание ThinkSystem NE0152T















































































































Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды

Lenovo ThinkSystem NE0152T, Руководство по установке

Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды