Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 41

Страница: 41 / 110

Chapter 3: Installing NE0152T Hardware and Options

To install the NE0152T in a System x or Power rack, complete the following steps:

Locate, record, and retain the product switch information in order to configure and
register your product. See

“Before Installing the NE0152T” on page 32

Note:

If this switch is a replacement switch, copy the product information from the

original switch onto the RID label that is shipped with replacement switch and
affix the new label to the bottom of the new switch.

Attach the front mounting brackets (Item 1) to each side of the switch with M4
screws (Item 2). Torque the screws to approximately 2.0 newton-meters (Nm) ± 0.1
Nm (17.7 inch-pounds).

Содержание ThinkSystem NE0152T















































































































Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды

Lenovo ThinkSystem NE0152T, Руководство по установке

Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды