Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 23

Страница: 23 / 110

Chapter 2: Switch Components

System Status LEDs

The following table describes the behavior of the system status LEDs:

Notes:



Support for the stacking feature depends on the installed firmware. To
determine whether your switch supports stacking, see the

Application Guide

for

your specific switch and firmware version.



If service required is due to a stacking error, this LED flashes or is steady green,
depending on its last known good state.

USB Port

The USB port enables you to connect a USB drive to the switch. You can copy files
from the switch to the USB drive, or from the USB drive to the switch. You can also
start the switch using files on the USB drive.

The supported file system formats for USB drives are FAT32 and NTFS (read-only).

Note:

When using a NTFS formatted USB drive, copying operations are limited to

read-only. Files can be copied from the USB drive to the switch, but copying files to
the NTFS formatted USB drive results in failure.

For more information about using the USB drive, see the

Lenovo ThinkSystem

NE0152T RackSwitch Application Guide

Table 4.

System status LEDs behavior

LED

State

Functional Meaning

All

Off

Total power failure.

- Service

Steady Blue

An operational command has been sent to light the
LED so that this device can be more readily located.

Flashing Blue

Service is required due to failure of the general system,
its cooling fans, stacking function

or its power supply.

The specific failure is indicated in conjunction with the
other system status LEDs.

- Power

Steady Green

Power supply is on and operational.

Flashing Green

Power supply failure or disconnection. Service is
required.

Off

Power supply shutdown. Service is required.

- Fans

Steady Green

Fans are on and operational.

Flashing Green

Fan failure. Service is required.

Off

Fan shutdown. Service is required.

- Stacking

Steady Green

Device is a Master in a stack.

Flashing Green

Device is the Backup/Member in a stack.

Off

Device is not a stacking member.

Содержание ThinkSystem NE0152T















































































































Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды

Lenovo ThinkSystem NE0152T, Руководство по установке

Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды