Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 109

Страница: 109 / 110

Appendix C: Technical Specifications

109

Switching Performance

The feature performance characteristics of the NE0152T are listed in the following
table.

Note:

The specific features supported on your switch, as well as some capacity and

performance characteristics, depend on the specific firmware installed. For more
information, see the

Application Guide

and

Command Reference

for your specific

switch and its installed firmware.

Table 16.

NE0152T feature performance characteristics

Feature

Characteristics

Switching architecture

Non-blocking

Throughput

88 Gbps full-duplex

Ethernet line rate

100%

IEEE 802.1Q VLANs

4096, with 4K VLAN IDs
up to 4092 VLANs can be configured

Forwarding database entries

65K

Configurable physical interfaces

53 (static or DHCP):
52 data ports + 1 management port

ARP entries

15872

Содержание ThinkSystem NE0152T















































































































Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды

Lenovo ThinkSystem NE0152T, Руководство по установке

Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды