Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 110

background image

© Copyright Lenovo 2018

Chapter 5: Initializing the NE0152T

81

Updating Firmware

If firmware updates are available, you can download them from the Lenovo
website. The switch might have features that are not described in the
documentation that comes with the switch, and the documentation might be
updated occasionally to include information about those features, or technical
updates might be available to provide additional information that is not included in
the switch documentation.

Unsaved configuration settings are lost during a firmware update. Before updating
the firmware, save a copy of the configuration to a separate device. In the event of a
failed update, the saved configuration can be restored. For more information about
the configuration file, see the

Application Guide

guide for your specific switch and

firmware version.

Attention:

Installing the wrong firmware update might cause the network switch

to malfunction. Before you install a firmware, read any release notes,

readme

files

and change history files that are provided with the downloaded update. These files
contain important information about the update and the procedure for installing
the update, including any special procedure for updating from an early firmware
version to the latest version.

To check for firmware and documentation updates, go to the Lenovo website:

http://support.lenovo.com/

Note:

Changes are made periodically to the Lenovo website. Procedures for

locating firmware and documentation might vary slightly from what is described
in this document.

«
...
79
80
81
82
83
...
»

Содержание ThinkSystem NE0152T















































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem NE0152T

Бренд: DANLERS Страницы: 2

COOPER POWER SERIES

Бренд: Eaton Страницы: 32

Бренд: Keithley Страницы: 452

Бренд: Under Control Страницы: 9

SmartSwitch 6500

Бренд: Cabletron Systems Страницы: 62

Бренд: LONG-JOIN Страницы: 2

Бренд: FCI Страницы: 12

Бренд: M-E Страницы: 36

Бренд: Kramer Страницы: 46

Бренд: Lantech Страницы: 80

FS5300-EI Series

Бренд: H3C Страницы: 57

EG5-0702-SFP Series

Бренд: Leonton Страницы: 21

Бренд: Tripp Lite Страницы: 12

Бренд: Omron Страницы: 13

Бренд: DataParts Страницы: 5

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 4

NetVanta 1570-24-370W

Бренд: ADTRAN Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды