Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 110

background image

54

NE0152T Installation Guide

To install an SFP+ optical transceiver in an SFP+ port slot on the switch, complete
the following steps.

Note:

To avoid damage to the cable or the SFP+ transceiver, do not connect the

cable before you install the transceiver.

1.

Remove the safety cap and pull the locking lever into the down (unlocked)
position.

2.

Insert the transceiver into the slot until it clicks into place. Use minimal pressure
when you insert the transceiver into the slot. Do not use excessive force when you
insert the transceiver or you might damage the transceiver or the slot.

Note:

The transceiver has a mechanical guide key to prevent you from inserting

the transceiver in an incorrect orientation.

3.

Pull up the locking lever to lock the transceiver into place.

4.

Connect the fiber-optic cable following the

“Cabling Guidelines” on page 36

.

To remove an SFP+ optical transceiver, disconnect the fiber-optic cable, and pull
down the locking lever to release the transceiver. After you remove the transceiver,
replace the safety cap.

«
...
52
53
54
55
56
...
»

Содержание ThinkSystem NE0152T















































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem NE0152T

Бренд: eao Страницы: 2

Бренд: eao Страницы: 2

RackSwitch G8264T

Бренд: IBM Страницы: 20

Бренд: BeeSecure Страницы: 35

Бренд: OEM Страницы: 1

Бренд: Cabletron Systems Страницы: 52

Бренд: Zamel Страницы: 2

Бренд: Atlantis Land Страницы: 3

UltraHD Switch 3:1

Бренд: Oehlbach Страницы: 20

Бренд: NTI Страницы: 69

JTECH-4KPIP0401

Бренд: J-Tech Digital Страницы: 10

PICO-GUARD SFI-D1EDPXT6

Бренд: Banner Страницы: 2

Бренд: Eagle Страницы: 2

CheetaHub Power-3004E

Бренд: Accton Technology Страницы: 11

Бренд: GoMax Electronics Страницы: 6

Бренд: WIKA Страницы: 52

Бренд: ATEN Страницы: 125

True Scale Fabric 12000 Series

Бренд: Intel Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды