Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 110

background image

26

NE0152T Installation Guide

Rear Panel

The rear panel is composed of the following components.

Fans

For cooling, the rear panel of the NE0152T has three bays for hot-swap fan modules.
Three fan modules are required for redundancy. When three fan modules are used,
if there is a failure of one of the fans, the switch reports the condition, the other fans
continue to run, and the switch continues to operate normally.

You can replace one failed hot-swap fan module while the switch is operating. If a
second fan fails, the switch reports the condition and shuts down to prevent
overheating.

CAUTION:
Be sure to finish the replacement procedure promptly. The switch could overheat
if left without cooling for an extended period.

Compatible fan options are listed in the

Lenovo Networking Catalog

Fan operation and internal temperatures are monitored. If the air temperature
exceeds a desired threshold, the environmental monitor displays warnings.

Note:

If a fan fails, the maximum operating temperature drops from +40°C (104°F)

to +35°C (95°F).

Fan LEDs

If there is a failure of one or more fans, the front panel Fan LED flash.

Additional Fan LED indicators are located on the rear panel of the switch, on the
individual fan modules.

The following table describes the fan module LED behavior.

Table 6.

Fan module status LED behavior

LED State

Functional Meaning

On

Fan is on and operational.

Off

Fan module has no power.

Flashing

Fan speed failure. Replace the fan module.

«
...
24
25
26
27
28
...
»

Содержание ThinkSystem NE0152T















































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem NE0152T

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: FAAC Страницы: 2

Бренд: PRO SIGNAL Страницы: 5

Бренд: Touch-plate Страницы: 12

Бренд: CGS Instruments Страницы: 39

SM24-1000SFP-AH

Бренд: Transition Networks Страницы: 76

Бренд: TE Connectivity Страницы: 32

Бренд: Exsys Страницы: 14

ScatterBox POE308

Бренд: System Q Страницы: 2

5-Port Gigabit Switch 1000 Mbps

Бренд: Hama Страницы: 2

ONW-D-1001-347-W

Бренд: Greengate Страницы: 2

Бренд: H3C Страницы: 4

LANPLEX 2500 EXTENDEDPLEX 2500 EXTENDED

Бренд: 3Com Страницы: 186

Бренд: SMART-AVI Страницы: 2

B-520-MTRX-230-6x4+2

Бренд: Binary Страницы: 32

Бренд: TESmart Страницы: 34

NetVanta 1560-48

Бренд: ADTRAN Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды