Lenovo ThinkSystem NE0152T Скачать руководство пользователя страница 64

Страница: 64 / 110

NE0152T Installation Guide

Removing the NE0152T from a Lenovo System x or Power
Rack

This section describes how to remove the NE0152T from a Lenovo System x or
Power 4-post rack.

To remove the NE0152T from a System x or Power rack, complete the following steps:

Disconnect all external cables.

If the air-duct option has been installed, remove it as described in

“Removing the

Air-Duct Option” on page 69

Loosen and remove M3.5 screws that secure the rear brackets to the front brackets.

Loosen and remove the M6 screws and clip nuts (or cage nuts) that attach the filler
plate and rear mounting brackets to the rear rack posts.

Содержание ThinkSystem NE0152T















































































































Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды

Lenovo ThinkSystem NE0152T, Руководство по установке

Результаты поиска

Содержание ThinkSystem NE0152T

Отзывы:

Похожие инструкции для ThinkSystem NE0152T

Бренды по названию

Популярные бренды