Leica TPS800 Series Скачать руководство пользователя страница 146

Страница: 146 / 204

146

File Management

Leica TPS800-4.0.0en

Fixpoints

Valid fixed points contain at least the PtID and the
coordinates (E, N) or (H).
[DELETE]

Deletes selected fixed point.

[FIND]

Starts point search. Exact PtIDs can
be entered or the * wildcard-criteria
used.

[NEW]

Opens input for PtID and coordi-
nates.

Measurements

Measurement data available in the internal memory
can be searched and displayed or erased.
[FIND]

Starts point search dialogue.

[VIEW]

Displays all measurements.

Codes

To each code a description and a maximum of 8
attributes with up to 16 characters can be assigned.

[SAVE]

Save data.

[VIEW]

Starts search dialogue.

[ATTRIB]

Input of attributes.

INPUT CODELIST

Code :

Nr01

Desc. :

border line

Info1 :

Nr. 123

Info2 :

12.54

Info3 :

Содержание TPS800 Series













































































































































































































Результаты поиска

Содержание TPS800 Series

Отзывы:

Похожие инструкции для TPS800 Series

Бренды по названию

Популярные бренды

Leica TPS800 Series, Руководство пользователя

Результаты поиска

Содержание TPS800 Series

Отзывы:

Похожие инструкции для TPS800 Series

Бренды по названию

Популярные бренды