Leica TPS800 Series Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 204

background image

168

Safety Directions

Leica TPS800-4.0.0en

and locked in position. Avoid subjecting the product
to mechanical stress.



Caution

During the transport, shipping or disposal of

batteries it is possible for inappropriate mechanical
influences to constitute a fire hazard.

Precautions:

Before shipping the product or disposing of it,
discharge the batteries by running the product until
they are flat.
When transporting or shipping batteries, the person
in charge of the product must ensure that the appli-
cable national and international rules and regula-
tions are observed. Before transportation or ship-
ping contact your local passenger or freight trans-
port company.



Warning

Using a battery charger not recommended by

Leica Geosystems can destroy the batteries. This
can cause fire or explosions.

Precautions:

Only use chargers recommended by Leica Geosys-
tems to charge the batteries.



Warning

High mechanical stress, high ambient

temperatures or immersion into fluids can cause
leackage, fire or explosions of the batteries.

Precautions:

Protect the batteries from mechanical influences
and high ambient temperatures. Do not drop or
immerse batteries into fluids.



Warning

Short circuited battery terminals can overheat

and cause injury or fire, for example by storing or
transporting in pockets if battery terminals come in
contact with jewelry, keys, metallized paper or other
metals.

Precautions:

Make sure that the battery terminals do not come
into contact with metallic objects.

«
...
166
167
168
169
170
...
»

Содержание TPS800 Series













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TPS800 Series

Бренд: dacell Страницы: 22

Бренд: jablotron Страницы: 2

NANOCOLOR Advance

Бренд: Macherey-Nagel Страницы: 45

Бренд: Nellcor Страницы: 104

Бренд: Vega Страницы: 20

Бренд: Vega Страницы: 16

Бренд: Vega Страницы: 2

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 38

Бренд: Yamaha Страницы: 45

Wind Monitor Series

Бренд: Campbell Страницы: 38

Бренд: Favero Electronics Страницы: 12

BUCKMASTERS 1500

Бренд: Sig Sauer Страницы: 2

WM14-96 - PROGRAMMING

Бренд: CARLO GAVAZZI Страницы: 6

Бренд: Xylem Страницы: 10

Бренд: Lasertec Страницы: 32

Бренд: IDEAL Страницы: 20

QI-POWER-485-300-LV

Бренд: QEED Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды