Leica TPS800 Series Скачать руководство пользователя страница 49

Страница: 49 / 204

Programs

Leica TPS800-4.0.0en

Orientation

With the orientation, Hz-direction can be input
manually or points with known coordinates can be
set.

Method 1: Manual input

To input a random Hz-orientation.

2. Input of Hz-direction, reflector height and PtID.
3. [ALL]

Triggers measurement and sets
orientation.

[REC]

Records Hz-direction and sets
orientation.

Method 2: With coordinates

To determine the orientation, a target with known
coordinates can also be used.
1.

As orientation with coordinates.

2. Input of the orientation point number and to

determine the point found.

3. To input and confirm the reflector height.
For determining the orientation a maximum of 5
target points with known coordinates can be used.

1) 1. Target point
2) 2. Target point
3) 3. Target point

TPS800_Z29

Содержание TPS800 Series













































































































































































































Результаты поиска

Содержание TPS800 Series

Отзывы:

Похожие инструкции для TPS800 Series

Бренды по названию

Популярные бренды

Leica TPS800 Series, Руководство пользователя

Результаты поиска

Содержание TPS800 Series

Отзывы:

Похожие инструкции для TPS800 Series

Бренды по названию

Популярные бренды