LEGRAND 422684 Скачать руководство пользователя страница 35

Страница: 35 / 48

Three-Sources Management System

(T.S.M.S.)

Installa

tion and user manual

CODE

DESCRIPTION

REASON FOR THE ALARM

A31

NPL (Non-Priority Load)

breaker timeout

The non-priority load breaker did not perform the opening or closing

operation before the timeout. The opening or closing control is inhibited

after the alarm has been generated. The alarms are only generated if one

of the power sources is present, i.e. higher than the minimum programmed

thresholds.

A32

QC - QC1 Tie breaker

timeout

Tie breaker QC - QC1 did not perform the opening or closing operation before

the timeout. The opening or closing control is inhibited after the alarm has

been generated. The alarms are only generated if one of the power sources is

present, i.e. higher than the minimum programmed thresholds.

A33

QC - QC2 Tie breaker

timeout

As above, referred to tie breaker QC - QC2.

A34

NPL (Non-Priority Load)

breaker protection trip

NPL breaker opened because its overcurrent protection tripped, as

indicated by the specific input with the NPL

breaker protection trip

function.

A35

QC - QC1 tie breaker

protection trip

QC1 - QC1 tie breaker opened because its overcurrent protection tripped,

as indicated by the specific input with the QC - QC1 tie

breaker protection

trip

function.

A36

QC - QC2 tie breaker

protection trip

As above, referred to QCQC2 tie breaker.

A37

NPL (Non-Priority Load)

breaker withdrawn

NPL breaker is not available because the input with the

NPL breaker

withdrawn

function indicates that the breaker is not present in its housing.

A38

QC - QC1 tie breaker

withdrawn

QCQC1 tie breaker is not available because the input with the

QC - QC1 tie

breaker withdrawn

function indicates that the breaker is not present in its

housing.

A39

QC - QC2 tie breaker

withdrawn

As above, referred to tie QC - QC2 breaker.

UA1…UA8 User alarms

The user alarm was generated by the activation of the variable or the

associated input by means menu M15.

2.24

Programmable input functions table

• The following table shows all the functions which can be associated to the programmable digital inputs INPn.

• Each input may be set so as to have inverted function (NO - NC) because the energising or de-energising may be reset

with independent times.

• Other functions require a further numeric parameter defined by index (x) specified by parameter P12.n.02.

• See menu

M12 Digital inputs

for more details.

NR.

FUNCTION

DESCRIPTION

Disabled

Disabled input.

Configurable

Freely configurable by the user.

Line 1 breaker closed

(Feedback Q1)

Auxiliary contact which informs the ref. 422684 of the open/closed

state of breaker Q1. If this signal is not connected,

ref. 422684 considers the state of the breaker corresponding to the

control output state.

Line 2 breaker closed

(Feedback Q2)

As above, referred to Q2.

Line 3 breaker closed

(Feedback Q3)

As above, referred to Q3.

Line 1 in breaker tripped

(Trip Q1)

The input generates breaker Q1 protection tripping when the contact

closes.

continue

Содержание 422684

















































Результаты поиска

Содержание 422684

Отзывы:

LEGRAND 422684, Инструкция по установке и эксплуатации, Страница: 35 / 48

Результаты поиска

Содержание 422684

Отзывы: