LEGRAND 422684 Скачать руководство пользователя страница 26

Страница: 26 / 48

P09.n.11, P09.n.12 - P09.n.11 These define the maximum imbalance threshold between the phases referred to rated

voltage and P09.n.12 is the respective tripping delay. This control may be disabled by setting P09.n.11 to OFF.

P09.n.13 - Maximum frequency tripping threshold; may be deactivated.

P09.n.14 - Maximum frequency tripping delay.

P09.n.15 - Minimum frequency tripping threshold; may be deactivated.

P09.n.16 - Minimum frequency tripping delay.

P09.n.17 - OFF = voltage control S.n in OFF mode is deactivated. ON = voltage control in OFF mode is active. OFF+GLOB

= voltage control in OFF mode is deactivated but the relay programmed with the global alarm function may

intervene or not according to whether the mains are absent or present, respectively. ON+GLOB = voltage

control in OFF mode is activated but the relay programmed with the global alarm function may intervene or not

according to whether the mains are absent or present, respectively.

P09.n.18 - See P09.n.17 but referred to MANUAL mode.

P09.n.19, P09.n.20 - Conditional enable of the source line. OFF = The source line is normally available. (Any other

setting) = The source line can be used only if the set variable is active.

M10 - COMMUNICATION

COMn (n=1…3)

UNIT

DEFAULT

RANGE

P10.n.01

➊

Serial node address

01-255

P10.n.02

➊

Serial speed

bps

19200

1200

2400

4800

9600

19200

38400

57600

115200

P10.n.03

➊

Data format

8 bit - n

8 bit, no parity

8 bit, odd

bit, even

7 bit, odd

7 bit, even

P10.n.04

➊

Stop bit

1-2

P10.n.05

➊

Protocol

Modbus RTU

Modbus ASCII

Modbus TCP

➊

These parameters are also accessible with user level password.

Note: This menu is divided into 3 sections for communication channels COM1..3.

The channel COM1 identifies the standard RS-485 port, while COM2 and COM3 are reserved to the possible

communication ports on expansion modules EXP. The infrared frontal programming port has fixed communication

parameters and no setting menu is reuired.

P10.n.01 - Serial address (node) of the communication protocol.

P10.n.02 - Communication port transmission speed (1200 bps not available on slot 1 and 4).

P10.n.03 - Data format. 7-bit settings available for ASCII protocol only.

P10.n.04 - Stop bit number.

P10.n.05 - Communication protocol selection.

P10.n.06, P10.n.07, P10.n.08 - TCP-IP coordinates for applications with Ethernet interface. Not used with other commu-

nication module types.

P10.n.09 - Port operating mode. Slave = normal operation, the device reply to the messages of an external master.

Gateway = The device analyses the message intended to it (serial address) and forwards those address to

other nodes through the RS485 interface.

2. Operating modes

Содержание 422684

















































Результаты поиска

Содержание 422684

Отзывы:

LEGRAND 422684, Инструкция по установке и эксплуатации, Страница: 26 / 48

Результаты поиска

Содержание 422684

Отзывы: