LEGRAND 422684 Скачать руководство пользователя страница 22

Страница: 22 / 48

P06.n.04 - Maximum cooling cycle time. Example: time which elapses between the load disconnection of the genset and

the actual stopping of the engine.

M07 - BREAKERS

(Qn, n=1…3)

UNIT

DEFAULT

RANGE

P07.n.01 Breaker description

(char*6)

P07.n.02 Interlock time SQ.x

➔

…

sec

6.0

0.1…1800.0

P07.n.03 Breaker operation max. time (alarm delay A03 and A04)

sec

1…900

P07.n.04 Open pulse time

sec

0-600

P07.n.05 Close pulse time

sec

0-600

P07.n.06 Continuous control in RESET/OFF mode

NOC

OFF

NOC

P07.n.07 Breaker following no closing (with feedback open only)

OFF

P07.n.08 Minimum coil opening pulse time

sec

1.0

0.1 … 10.0

P07.n.09 Delay between min. coils and spring load

sec

0.2

0.1 … 10.0

P07.n.10 Closing retry

AUT

OFF

AUT

AUT+MAN

CLOSING

P07.n.11 Breaker conditional enable

OFF

INPx

OUTx

LIMx

REMx

PLCx

UAx

P07.n.12 Function index (x)

OFF

OFF / 1…99

Note: This menu is divided into 3 sections for controlling the source line breakers Q1..3.

P07.n.01 - Alphanumeric description which identifies the line breaker on the display synoptic panel.

P07.n.02 - Interlock time from the opening instant of the breaker n to the closing of another breaker.

P07.n.03 - Timeout between sending of a control from a line breaker and the actual execution of the operation. After

having sent an opening or closing control to the breaker, alarms A03 or A04 are generated if it is not positio-

ned correctly before the timeout. It works when the auxiliary state contacts of the breakers is programmed

and wired.

P07.n.04 - Minimum opening control time, when the breaker control is defined by means of a pulse (P08.01 = Pulse

breaker). For applications with motorised line breakers, this must be set to a sufficient time to allow complete

charging of the springs. This time is considered also when working in continuous control mode.

P07.n.05 - Closing control pulse time.

P07.n.06 – Otherwise, the breaker control is selected as continuous (P08.01 = Continuous breaker), defines the behaviour

of the board when it switches to the OFF operating mode. OFF = The control relays are de-energised. NOC =

The control relays remain in in their original state (No Change).

P07.n.07 - In case of timeout caused by the line breaker n failing to close (open feedback contact) causes the transfer of

the load on an alternative line.

P07.n.08 - Minimum coil deactivation pulse duration for breaker opening pulse.

P07.n.09 - Time elapsed between minimum voltage opening pulse and breaker spring loading control.

P07.n.10 - This defines whether in case of failure to close the ref. 422684422684 must perform a retry consisting of a

cycle of opening/spring recharging cycles followed by a new closing attempt. The failed closing alarm will be

generated if the second attempt also fails. OFF = Closing is not retryed.

AUT = Retry is manual only. AUT+MAN = Retry enabled in both modes. CLOSING = Closing retry is executed

in AUT or MAN only in case of failed closing but not when breaker opens unexpectedly.

P07.n.11, P07.n.12- Conditional enable of breaker. OFF = Breaker is enabled normally. (Any other setting) = The brea-

ker is enabled only if the selected variable is active. When the variable is not active, if the breaker is open, its

closing will be avoided. If the breaker is closed, it will be opened.

2. Operating modes

Содержание 422684

















































Результаты поиска

Содержание 422684

Отзывы:

LEGRAND 422684, Инструкция по установке и эксплуатации, Страница: 22 / 48

Результаты поиска

Содержание 422684

Отзывы: