Kyocera TASKALFA 300I Скачать руководство пользователя страница 95

Страница: 95 / 408

2K5

1-3-59

U243

Checking the operation of the DP motors
Description

Turns the motors or solenoids in the DP on.

Purpose

To check the operation of the DP motors and solenoids.

Method

1. Press the start key.
2. Select the item to be operated.
3. Press the start key. The operation starts.

4. To turn each motor off, press the stop key.

Completion

Press the stop key when operation stops. The screen for selecting a maintenance item No. is displayed.

U244

Checking the DP switches
Description

Displays the status of the respective switches in the DP.

Purpose

To check if respective switches in the DP operate correctly.

Method

1. Press the start key.
2. Turn the respective switches on and off manually to check the status.

If the on-status of a switch is detected, the corresponding switch is displayed in reverse.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Motor and solenoid

Operation

DP FEED MOT

Original feed motor (OFM)

In operation

DP CON MOT

Original conveying motor (OCM)

In operation

DP REV MOT

Original switchback motor (OSBM)

In operation

DP RP SOL

Switchback pressure solenoid (SBPSOL)

On for 0.5 s

DP RJ SOL

Switchback feedshift solenoid (SBFSSOL)

On for 0.5 s

Display

Switches

TMG SW

DP timing switch (DPTSW)

REV SW

Original switchback switch (OSBSW)

SET SW

Original set switch (OSSW)

SZ SW A

Original size length switch (OSLSW)

COV OP SW

DP interlock switch (DPILSW)

DP OP SW

DP open/close switch (DPOCSW)

Содержание TASKALFA 300I

























































































































































































































































































































































































































Результаты поиска

Содержание TASKALFA 300I

Отзывы:

Похожие инструкции для TASKALFA 300I

Бренды по названию

Популярные бренды

Kyocera TASKALFA 300I, Руководство по обслуживанию

Результаты поиска

Содержание TASKALFA 300I

Отзывы:

Похожие инструкции для TASKALFA 300I

Бренды по названию

Популярные бренды