manualshive.com logo in svg

Kyocera TASKALFA 300I, Руководство по обслуживанию

Kyocera TASKalfa 300i - мощное многофункциональное устройство для офиса. Вы можете скачать бесплатно сервисный мануал для этого устройства на manualshive.com. Получите подробное руководство по обслуживанию и настройке устройства, чтобы обеспечить его долгий срок службы и бесперебойную работу.

Поделиться
Скачать
background image

14

a

1

h

2

X

X’

i

X’

X

X’

X

100

+1.5%

-1.5%

X

2

Überprüfen der Vergrößerung

Die Abweichung der Linie (1) des Originals (a) und der Linie (2) des 
Kopienmusters prüfen. Überschreitet die Abweichung den Bezugswert, ist 
die folgende Einstellung durchzuführen.
Bezugswert: Innerhalb ±1,5 %

Einstellen der DP-Vergrößerung

1.

Den Wartungsmodus aktivieren, und den Wartungsposten U070 zur 
Einstellung ausführen.
Für erste Seite: [MOTOR ADJ(FRONT)] wählen.
Für zweite Seite: [MOTOR ADJ(BACK)] wählen.

Verificación del cambio de tamaño

Verifique la separación entre la línea (1) del original (a) y la línea (2) de la 
copia de muestra. Si la superación supera el valor de referencia, haga el 
siguiente ajuste.
Valor de referencia: Dentro de ±1,5 %

Ajuste del cambio de tamaño

1.

Entre en el modo de mantenimiento e ingrese en el ítem de 
mantenimiento U070 para ajustar.
Para el primer lado: Seleccione [MOTOR ADJ(FRONT)].
Para el segundo lado: Seleccione [MOTOR ADJ(BACK)].

Vérification de l’agrandissement

Vérifiez l’écart entre la ligne (1) de l’original (a) et la ligne (2) de l’exemple 
de copie. Si l’écart est supérieur à la valeur de référence, effectuez le 
réglage suivant.
Valeur de référence: ±1,5% max.

Réglage de l’agrandissement du DP

1.

Passez en mode de maintenance et exécutez l’élément de 
maintenance U070 pour effectuer le réglage.
Pour le recto: Sélectionnez [MOTOR ADJ(FRONT)].
Pour le verso: Sélectionnez [MOTOR ADJ(BACK)].

Controllo dell’ingrandimento

Controllare la differenza tra la linea (1) dell’originale (a) e la linea (2) della 
copia di esempio. Se la differenza supera il valore di riferimento, effettuare 
la seguente regolazione.
Valore di riferimento: Entro ±1,5 %

Regolazione dell’ingrandimento DP

1.

Entrare in modalità manutenzione e avviare la voce di manutenzione 
U070 per la regolazione.
Per il primo lato: selezionare [MOTOR ADJ(FRONT)].
Per il secondo lato: selezionare [MOTOR ADJ(BACK)].

确认等倍值

确认原稿 (a) 线 (1) 和复印样本线 (2) 的偏移。如果超过标准值时，必须进
行调整。
< 标准值 > ± 1.5％以内

调整 DP 等倍值

1. 设定为 U070 保养模式，进行调整。

表面时 ：选择“MOTOR ADJ(FRONT)”。
背面时 ：选择“MOTOR ADJ(BACK)”。

等倍度確認

原稿 (a) の線 (1) とコピーサンプルの線 (2) のずれを確認する。ずれが基
準値外の場合は調整をおこなう。
＜基準値＞± 1.5% 以内

DP 等倍度調整

1.

メンテナンスモード U070 をセットし、

調整をおこなう。

表面の場合：

「MOTOR ADJ(FRONT)」を選択する。

裏面の場合：

「MOTOR ADJ(BACK)」を選択する。

Checking the magnification

Check the gap between line (1) of original (a) and line (2) of copy 
example. If the gap exceeds the reference value, perform the following 
adjustment.
Reference value: Within ±1.5 %

Adjusting the DP magnification

1.

Enter the maintenance mode and run the maintenance item U070 to 
adjust.
For first side: Select [MOTOR ADJ(FRONT)].
For second side: Select [MOTOR ADJ(BACK)].

Содержание TASKALFA 300I

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TASKALFA 300I

QMS 2001 Setup Manual preview
2001
Бренд: QMS Страницы: 26
Olympus P-10 Supplementary Manual preview
P-10
Бренд: Olympus Страницы: 2
Olympus P-10 Instruction Manual preview
P-10
Бренд: Olympus Страницы: 148
Xerox VersaLink B415 User Manual preview
VersaLink B415
Бренд: Xerox Страницы: 324
Durst Rho 600 Pictor Specifications preview
Rho 600 Pictor
Бренд: Durst Страницы: 2
Quest Payment Systems Donation Point Even Quick Start Manual preview
Donation Point Even
Бренд: Quest Payment Systems Страницы: 2
Olivetti PGL 12EN Operator'S Manual preview
PGL 12EN
Бренд: Olivetti Страницы: 139
Triumph Adler P-6038i Quick Manual preview
P-6038i
Бренд: Triumph Adler Страницы: 4
SPRT SP-POS587 User Manual preview
SP-POS587
Бренд: SPRT Страницы: 13
Xerox AltaLink C81 Series User Manual preview
AltaLink C81 Series
Бренд: Xerox Страницы: 412
Epson 10600 - Stylus Pro Color Inkjet Printer Specification Sheet preview
10600 - Stylus Pro Color Inkjet Printer
Бренд: Epson Страницы: 8
Epson 1400 - Stylus Photo Color Inkjet Printer Specifications preview
1400 - Stylus Photo Color Inkjet Printer
Бренд: Epson Страницы: 8
Epson 10600 - Stylus Pro Color Inkjet Printer Printer Manual preview
10600 - Stylus Pro Color Inkjet Printer
Бренд: Epson Страницы: 183
Epson 1010 User Manual preview
1010
Бренд: Epson Страницы: 279
Epson 1400 - Stylus Photo Color Inkjet Printer Brochure & Specs preview
1400 - Stylus Photo Color Inkjet Printer
Бренд: Epson Страницы: 4
KOMDRUCK IDP-2103 Quick Manual preview
IDP-2103
Бренд: KOMDRUCK Страницы: 8
Muton VJ-1626UH Installation Manual preview
VJ-1626UH
Бренд: Muton Страницы: 16
Sharp MX-C250F Brochure & Specs preview
MX-C250F
Бренд: Sharp Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды